一二三四av_wwwxxx国产_亚洲精品久久久一区二区三区_久久久久91_亚洲一二三区在线观看_日日操视频

Mortar mixer introduction: mortar mixer is our own research and development of a new generation of to cooperate to promote the implementation of the national ministry of construction of (JGJ70-90) "building mortar basic performance test method standard" designed for the special equipment for mortar mixer.

Mortar mixer function characteristics: equipment can meet the performance requirements of dry mortar, dry material, adhesive powder production needs, such as: putty powder, powder coating, masonry mortar, plaster mortar, insulation mortar, decorative mortar needed by the system and so on all kinds of dry powder mortar; It has many advantages, such as small area, less investment, quick effect and simple operation.

Ii. Technical indicators:

1. Stirring blade speed: 48 + / -2r /min

2. Mixing tank capacity: 15L

Iii. Working principle of structure:

The machine is composed of frame, agitator, drive system, limit device and electric control system.

Frame is supporting part of the entire device, the channel steel welded together, mixing plant by mixing barrel, stirring shaft, stirring spade pieces of stirring spade piece fixed on the stirring arm, and with the stirring shaft of a body form two groups of opposite direction from the spiral, but equal helix Angle and lead helical ribbon stirring spade, shovel stir and stir within the cylinder clearance can be adjusted trace.

The drive mechanism consists of a reducer and a coupling. The cylinder body limit device consists of a locking pin and a positioning hole.

Working principle: reducing motor make the stirring shaft via the connecting shaft rotate along one direction, positive and negative two group shovel patches on the stirring shaft of mixing material, due to the effect of helix Angle, shovel piece of work make the material inside the drum from one side to the other side, and by the other side of the back of his place in the circulation, fully mixing of material, can achieve the ideal mixing effect.

When discharging, stop the machine, open the lock pin, make the cylinder body rotate at a certain Angle, relimit the position, press the point button to discharge the mixture out of the cylinder.

 Iv. Installation:

Machine after unpacking should check the gear motor, cylinder, bearing is damaged in transit, such as fasteners for loose, if there is loose should tighten, support the foundation for the formation of concrete ground, mixer to application in the ropes on the rack, cannot be set on the stirring shaft, stirrer pedestals of trundle, move can be arbitrary.

V. operating procedures:

1. Check whether there is any scratch between the rotating part and the feeding tube before starting, and adjust in time if there is any scratch.

2. Clean up the debris in the feeding tube.

3. The cylinder shall be limited before starting.

4. The rotation direction of the mixing shaft shall be shown as the mark on the end face of the cylinder body.

5. The loaded concrete materials must be cleaned of metal or other sundries.

6. Adjust the time of the agitator according to the stirring time, and pay attention to the adjustment in case of power failure.

7. Press the start button, and the spindle will drive the stirring shovel.

8. Stop automatically after reaching the set time.

9. When unloading, stop the machine first, open the lock pin, move the handle to rotate the cylinder to a certain position, and then make the lock pin locate the rotating spindle, so that the mixture can be discharged out of the cylinder.

10. After the mixture is cleaned, manually reset the cylinder body and position the mixing cylinder with the locking pin.

11. The cleaning material cylinder can pour water into the material cylinder to make the spindle rotate for washing. It can also be cleaned with dry sand.

Vi. Maintenance and maintenance:

1. Regularly lubricate the bearing parts according to the usage, and refer to the product manual for lubrication of the reducer.

2. Check the sealing condition of the machine regularly, and check the quality of the sealing gasket in time if there is any leakage.

3. Regularly check the fastening of the shovel, and tighten it in time if there is any loosening.

4. Regularly check whether the electrical control system is in good contact and dry condition.

5. After long-term use of the blender, the spatula and agitator should be worn out and adjusted or replaced according to the wear conditions.

6. Do not insert hands and rods into the cylinder during the mixing process to avoid